Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Lawrenceville, GA
Gate repair in Lawrenceville usually costs between $185 and $480 for the most common fixes: hinge replacement, post realignment, operator adjustments, and electrical troubleshooting. What makes Lawrenceville jobs different is the housing stock. Thousands of HOA entrance gates went in during the 1990s and 2000s subdivision boom, and they’re now hitting the same repair cycle at the same time. Call (877) 610-2993 and a live person answers.
Why Lawrenceville Homes Are Different
Gwinnett County’s red expansive clay is the main reason Lawrenceville gates fail the way they do. The soil swells in wet winters and shrinks in dry summers, which heaves post footings out of plumb. A gate that’s out of line by half an inch at the post is out of line by four inches at the latch. That’s the failure we see most often across the 30042, 30043, 30044, and 30045 corridors.
There’s also a Lawrenceville-specific problem most homeowners don’t know about until Hal points it out. Many subdivisions platted during the 1990s buildout installed single-post swing gates on shallow footings sized for a lighter aluminum panel. When HOAs later upgraded to heavier ornamental iron, the original posts were left in place. Those undersized, clay-heaved posts are now the leading failure point on service calls. Add in the humid subtropical climate accelerating rust on ornamental steel panels near the South Fork Peachtree Creek and Alcovy River drainages, and you have a repair market unlike anything in newer counties.
Gate Repair in Lawrenceville
Gate repair in Lawrenceville typically runs $185 to $480 for most common fixes. We work on swing gates, slide gates, and pedestrian gates across every Lawrenceville ZIP code, and most repairs are done same-day or next-morning. The gate stays in your driveway. We weld on site, quote the price before any work begins, and stand behind the job with the 90-Day Done Right Promise in writing. If you need a deeper look at what we do, Gate Repair covers the full scope.
Hinge & Post Repair
This is the repair we do most often in Lawrenceville because the red clay under most of this county is unforgiving. A typical hinge post replacement or reinforcement runs $240 to $520 depending on how deep the original footing goes and how far out of plumb it’s heaved. We excavate around the post, reset it below the clay swell line, and weld in a reinforcement gusset where the geometry demands it. If the panel is still straight, the post is the fix. Swapping the panel without addressing the post means you’ll fix it twice.
Gate Realignment
A gate that drags on the concrete or won’t latch cleanly is usually a post problem, not a panel problem. In Lawrenceville, realignment typically runs $160 to $340, and most of that is labor, not parts. We level the panel, reset the hinge geometry, and make sure the operator isn’t fighting a gate that’s trying to swing uphill. On slide gates, we check the rack and pinion alignment too, because a clay-shifted post that pulls the rail out of line will chew through gear teeth on a 15-year-old operator in a matter of months.
Electric Gate Repair
Electric gate repair in Lawrenceville runs $200 to $600 depending on whether it’s the operator motor, the control board, or a low-voltage wiring fault. The operators we see most often on Lawrenceville’s 1990s-era subdivision gates are Apollo and LiftMaster, and many still use their original control boards. Those boards fail predictably after 15 to 20 years of Georgia humidity and voltage spikes. We stock common parts for these brands, so a board replacement is often done same-day rather than waiting on a distributor across the country. We service Linear, Viking, and DoorKing units as well.
Automatic Gate Repair
Automatic gate repair covers the operator, the safety edges, the photo eyes, and the limit switches. In Lawrenceville, this work runs $190 to $575 depending on how much of the system is original. A lot of gates installed before 2008 don’t have modern entrapment protection, which means they’ll keep running if something gets caught in the pinch point. That’s a serious safety gap, and we flag it every time we see it. The fix is often a retrofit: adding safety edges and updated controls to the existing operator.
How much does gate repair cost in Lawrenceville?
Most Lawrenceville gate repairs run $185 to $480. Hinge and post work lands between $240 and $520, realignment between $160 and $340, and electric or automatic operator repairs between $190 and $600. The price we quote is the price on the invoice, agreed in writing before we touch a single bolt. Call (877) 610-2993 for a free estimate.
Do so many Lawrenceville HOA gates in the 30043 and 30044 ZIP codes fail at the hinge post rather than the panel?
Because the hinge post was undersized to begin with, and then the red clay did the rest. During the 1990s buildout, production builders poured shallow footings sized for lightweight aluminum panels. When HOAs later upgraded to ornamental iron, the original posts stayed in place. The panel is usually fine. The post is what’s tired.
Gate Installation in Lawrenceville
Gate installation in Lawrenceville isn’t a one-size-fits-all job, and if you’ve lived here through a few wet winters and dry summers, you already know the clay soil does things to posts that sandier counties never have to think about. We install driveway gates, pedestrian gates, sliding gates, and swing gates across Lawrenceville every week, and we know which subdivisions were built with operators that flunk today’s safety standards. Hal Gatewood has been running Gatewood Fence & Gate since 2001, and the name is on every invoice. Gate Installation details the full process.
Driveway Gate Installation
Most of the driveway gates we install in Lawrenceville are aluminum-frame or ornamental steel swing gates at subdivision entries or on individual estate lots. The post setup matters more than the gate panel, especially in the 30042 and 30045 areas where the red clay heaves every season. A single driveway swing gate installation runs $3,500 to $9,000 when you’re setting new posts. We set posts deeper than the old minimum standards and brace them for the gate weight plus a decade of wet-dry cycles.
Pedestrian Gate Installation
Pedestrian gates at HOA pools, tennis courts, and walking trails around Lawrenceville have their own failure pattern: the hinge side gets pried or climbed, the latch gets slammed, and the closer gives up. A pedestrian gate installation typically runs $1,200 to $3,800 depending on panel material and hardware. We install gates that swing smoothly and close quietly, sized for the traffic they actually get, with hardware that doesn’t need adjusting every other month.
Sliding Gate Installation
Sliding gates make sense on Lawrenceville properties with steep driveways or tight off-street space, but they live and die by the track and the roller trucks. Sliding gate installations start around $5,000 and go up with track length and automation. The clay here works fine for sliding gates so long as the track bed is laid on a real gravel base, which is not what the original builders always did in the 1990s. We weld and anchor the track on site, and stock common replacement rollers so you’re not waiting on a parts shipment if one wears out later.
Swing Gate Installation
Swing gates are the workhorse of Lawrenceville neighborhoods built between 1988 and 2008. A double swing gate with an operator lands closer to $7,000 to $16,000. Single-post swing gates from that era often carry a panel heavier than the post footing was ever meant to hold, and the clay makes it worse. We set new posts in concrete with proper diameter and depth, and we don’t leave an undersized post in place just because it’s easier. If the gate is going to swing, the post has to stay put.
Do you work with Lawrenceville HOAs on subdivision entrance gates?
Yes, we work with Lawrenceville HOA boards regularly, and we know the approval process in the 30045, 30046, and 30049 areas well enough to help you prepare the submission. We’ll provide spec sheets, finish samples, and whatever drawings the architectural committee asks for. Call (877) 610-2993 and we’ll walk you through it.
Can you install a gate if my Lawrenceville driveway is steep or narrow?
We do it all the time. Steep drives often get a sliding gate or a swing gate with a proper slope adjustment, and narrow lots usually work best with a side-mounted slide rather than a swing. We’ll measure what you have and tell you what actually works, not just what’s easiest to sell. Call (877) 610-2993 and we’ll set a free measure.
Gate Motor & Opener in Lawrenceville
A gate motor or opener replacement in Lawrenceville typically runs $600 to $1,850 depending on whether you’re swapping the operator only or adding safety retrofits, and most repairs land between $180 and $520. We’ve been called out to subdivisions along Simonton Road, Sugarloaf Parkway, and the Grayson Highway corridor enough times to know exactly what builder-grade operators from the late 1990s do when they start failing. If your HOA gate is stuck open, stalling mid-cycle, or making that grinding noise that echoes down the block, Gate Motor & Opener has the details.
Motor Repair
Most Lawrenceville motor failures are electrical, not mechanical. Motor repair on a swing or slide gate typically runs $180 to $520 depending on whether it’s a capacitor swap, a board replacement, or a limit switch rebuild. Control boards from the 1990s short out, capacitors dry up, and loop detectors stop reading vehicles. We diagnose on site and repair what’s actually broken. If Hal can solder a board back to life for $120, he won’t sell you a $900 operator you don’t need.
Motor Installation
When an old Apollo or LiftMaster operator finally gives out, we’ll pull the dead unit and install a replacement that fits your existing mounting plate and conduit. New operator installation with the gate already in place runs $850 to $1,850 for a residential-grade unit from Linear, Viking, or DoorKing, including programming and safety checks. We stock parts locally so Lawrenceville customers aren’t waiting two weeks on a freight shipment. Installation includes programming, limit setting, and a load test on the gate itself.
Photo-Eye Retrofit
The 2008 UL 325 entrapment-protection mandate came years after Lawrenceville’s 1990s and early 2000s HOA subdivisions installed their gate operators. Those original units lack the photo-eyes now required on automated gates. A photo-eye retrofit on a pre-2008 operator runs $150 to $400 per gate depending on existing conduit. We retrofit photo-eye kits on almost every older Lawrenceville HOA gate we touch, because a gate that won’t reverse when something blocks it is a safety hazard, not just an inconvenience.
Post Realignment & Re-Bedding
Post realignment and re-bedding costs $350 to $900, which matters because ignoring a heaving post destroys the new motor you just paid for. Gwinnett County’s expansive clay swells in winter and shrinks in summer, tilting hinge posts out of plumb. That makes the motor stall mid-cycle and the gate sag on the latch side. We re-bed posts with deeper concrete and re-align the operator so it’s not fighting the leaning post.
Why do so many Lawrenceville HOA gates from the 1990s need a photo-eye retrofit?
Because the UL 325 standard requiring entrapment protection took effect in 2008, years after most Lawrenceville subdivision gates were installed. Those original Apollo and LiftMaster units were legal when they went in, but they lack the photo-eyes now required. When the control board ages, the gate can move unpredictably. The fix is straightforward, and we do it regularly. Call (877) 610-2993 to schedule a look.
My subdivision’s swing gate sags on the latch side. Do we need a new panel or just a motor adjustment?
Almost never the panel. The sag comes from the hinge post, not the gate itself. In Lawrenceville, expansive red clay swells through wet winters and shrinks during dry summers, which heaves post footings out of plumb. The motor then has to push a gate that’s leaning against its own hinge, and it stalls. We align the post, re-bed the footing deeper if needed, and set the motor limits to match the corrected geometry.
Gate Access Control in Lawrenceville
Gate access control in Lawrenceville usually means one of two jobs: keeping a 1990s HOA entrance gate from locking out half the subdivision, or adding keypad entry, video intercom, or smart access to a gate that was built manual. We do both. Gatewood Fence & Gate has repaired and upgraded gate operators across every ZIP in Lawrenceville, and Hal Gatewood still answers the phone. If your gate keypad is dead after a storm off the Alcovy River, Gate Access Control has what you need.
Keypad Entry
A working keypad keeps residents moving and visitors honest. A typical keypad entry repair or replacement in Lawrenceville runs $220 to $480. Most of the keypads on subdivision gates are wired into operators from the late 1990s that lose their programming after a hard Georgia thunderstorm. When that happens, every code wipes back to factory default and nobody gets in. We replace failed keypads, rebuild corroded wiring at the pedestal, and often add a battery backup so the next storm off the South Fork Peachtree Creek doesn’t erase everything again.
Video Intercom
Most Lawrenceville townhome clusters and newer communities off Old Peachtree Road were built without video intercom. The gate had a keypad and that was the end of it. A full video intercom add-on, including the camera, power supply, and wiring adaptation to a legacy operator, runs $1,200 to $2,800 depending on gate length and whether we can reuse existing conduit. Adding video intercom now usually means working around the original conduit run, which was sized for two or three conductors and nothing more. We’ve pulled new circuits and surface-mounted conduit where the original trench through the asphalt entrance lane can’t be touched.
Smart Access
Smart access in Lawrenceville usually means letting residents open the gate from a phone app instead of digging a gate remote out of the cup holder. A smart access retrofit on a Lawrenceville subdivision gate runs $650 to $1,400 depending on the operator’s condition. The hard part here isn’t the app; it’s the legacy operator on the other end. A 1998 LiftMaster or Apollo wasn’t built for wireless credentialing. We add a modern receiver, wire it into the operator’s open-command terminals, and configure the admin panel so the HOA board controls who has access.
Card Reader Replacement
Some Lawrenceville HOA gates still carry the old square metal card readers from the original build. Most card reader replacements in Lawrenceville come in between $280 and $600, installed. They’re dated, they wear, and the readers themselves often get confused when a resident holds a cell phone too close. But replacing them doesn’t have to mean replacing the operator. We’ll pull the old reader, mount a new proximity reader at the same pedestal, and hand the board a batch of new cards or fobs.
Why do so many Lawrenceville HOAs need safety upgrades on a gate access control system that still opens and closes fine?
Because nearly every entrance gate installed during Lawrenceville’s 1990s and 2000s subdivision boom predates the 2008 UL 325 entrapment-protection mandate. The gate still cycles, so nobody notices the missing safety edge or non-compliant photo-eye. But if someone or a car gets caught in that gate, the HOA and the operator owner are both exposed. We retrofit UL 325-compliant photo-eye circuits and safety edges on every access control job in Lawrenceville. Call (877) 610-2993 to schedule an inspection.
Can we add video intercom to a gate access system that’s been using the same keypad since 1998?
Yes, and we do it regularly in Lawrenceville. The challenge is the original conduit run, which was sized for a keypad and maybe a phone entry line, with no spare conductors. We’ll surface-mount new low-voltage conduit along the gate frame, pull the video and audio wiring, and install a camera and two-way talk at the pedestal. The old keypad stays or gets replaced, whichever the HOA board wants.
Gate Parts & Welding in Lawrenceville
If you live in Lawrenceville and your subdivision gate is sagging, dragging, or hanging off a weld, the cause is usually the same: a hinge post leaning out of plumb in Gwinnett’s red clay. Gate parts and welding in Lawrenceville runs $180 to $340 for most hinge and bracket repairs, $350 to $800 for post replacement, and $95 to $150 per hour for on-site custom welding. We have been fixing gates since 2001, and Hal Gatewood’s name is on every invoice. Gate Parts & Welding covers the full scope of what we fabricate and repair.
Hinge Replacement
Worn hinge pins are the quiet killer of Lawrenceville’s swing gates. Hinge replacement in Lawrenceville typically runs $180 to $340 per leaf, including on-site welding. The pin grinds down, the leaf drops a half inch, and pretty soon the operator is fighting the gate instead of moving it. We replace hinges on ornamental iron and aluminum gates, welding the new barrel and pin in place rather than bolting on a bracket that will work loose in a year.
Post Replacement
This is the biggest single repair in Lawrenceville’s subdivisions. Post replacement usually runs $350 to $800 depending on post size and access. The gate sags in the post, not in the middle. Gwinnett’s expansive clay swells in wet winters and shrinks in dry summers, heaving shallow post footings out of plumb. We cut the old post at grade, pour a new 48-inch footing with rebar, set a new post, and weld the hinges back on.
Rail Repair
On ornamental iron gates, the bottom rail takes the abuse. Rail repair with on-site welding typically runs $120 to $300 in Lawrenceville. It drags, it bends, it rusts through in the humid summers. We straighten bent rails, weld cracked joints, and splice rusted sections. If the top rail is bowing, that usually means the hinge post has moved, so we check the post before we touch the rail.
Custom Welding
Some things are not in a parts catalog. Custom welding in Lawrenceville runs $95 to $150 per hour plus materials, and the price is quoted and agreed before any work starts. A bracket for a modern safety sensor on a 1998 Apollo operator, a reinforcement plate for a cracked post cap, a custom mount for a new keypad on an old brick column. Hal welds on site, usually same visit.
Do you weld ornamental iron gates on site in Lawrenceville, or do you take the panel to a shop?
We weld on site. The gate stays in your driveway. Hal’s truck carries a welder, grinding gear, and stock plate steel, so most hinge, rail, and bracket repairs are done in one visit. We do not haul your gate to a shop and leave the opening unsecured. That is the whole point of our Gate Parts & Welding service. Call (877) 610-2993 to schedule a repair.
The gate posts in my Lawrenceville subdivision were fine for years, but now the gate drags after every rainy season. What’s happening?
That is the red clay at work. Gwinnett County’s soil expands when it absorbs winter rain, lifting the footing a fraction of an inch. In summer, the clay dries and shrinks. Over repeated seasons, the footing works its way loose, the post leans, and the gate leaf drops enough to drag on the drive. Lower-lying subdivisions near the South Fork Peachtree Creek and Alcovy River drainages see it worst.
Brands We Service in Lawrenceville
We stock common parts and service boards for Linear, Viking, Ghost Controls, and DoorKing operators in Lawrenceville. Most board replacements and common repairs happen same-day because the parts are already on the truck, not waiting on a freight shipment. See our brands for the full list of what we work on.
Pricing for Gate Repair in Lawrenceville, GA
| Service | Typical range in Lawrenceville |
|---|---|
| Hinge & post repair | $240 - $520 |
| Gate realignment | $160 - $340 |
| Electric gate repair | $200 - $600 |
| Automatic gate operator repair | $190 - $575 |
| Weld & rust repair | $90 - $300 |
| Pedestrian gate installation | $1,200 - $3,800 |
| Single driveway swing gate installation | $3,500 - $9,000 |
| Double swing gate with operator | $7,000 - $16,000 |
| Sliding gate installation | $5,000+ |
| Photo-eye retrofit | $150 - $400 |
| Post realignment & re-bedding | $350 - $900 |
| Custom welding (per hour) | $95 - $150 |
What pushes price up in Lawrenceville is almost always the clay. Deeper and wider footings cost more than minimum-code pours, and older gates with pre-2008 operators often need safety retrofits added to the original scope. Every price is quoted and agreed before the work starts. The number we give you on the phone is the number on the invoice. That’s the point.
Neighborhoods We Serve in Lawrenceville
We work across all four Lawrenceville ZIP codes: 30042, 30045, 30046, and 30049. Response time for gate repair in Lawrenceville is typically same-day or next-morning. We’re familiar with the gate hardware and soil conditions in these neighborhoods:
- Springlake Cove and the Flowers Crossing area
- Sugarloaf corridor neighborhoods
- Collins Hill Road subdivisions
- Townhome communities along Old Norcross Road
Service Area - Cities Near Lawrenceville
Gatewood Fence & Gate serves Lawrenceville, GA and the surrounding Gwinnett County communities. We regularly work in Lilburn, GA, Norcross, GA, Duluth, GA, Suwanee, GA, and Snellville, GA. Dispatch and scheduling are coordinated from our Atlanta office, and crews serve Lawrenceville locally.
Serving Lawrenceville, GA - Our Local Coverage Area
Gatewood Fence & Gate crews serve Lawrenceville and the communities around it; dispatch is coordinated from our Atlanta office. The map shows the Lawrenceville coverage area; if your address is on it, we can help.
Also serving nearby: Lawrenceville, GA, Lilburn, GA, Norcross, GA, Duluth, GA, Suwanee, GA, Snellville, GA.
FAQs About Gate Repair in Lawrenceville
Most gate repairs in Lawrenceville are handled same-day or next-morning. If your gate is stuck open and the property is unsecured, we prioritize those calls. Call (877) 610-2993 and a live person answers around the clock, not a voicemail. We’ll tell you exactly when someone will be there.
For repairs that match the existing hardware and finish, most Lawrenceville HOAs don’t require additional approval. For installations or significant changes, the architectural committee usually wants spec sheets and finish samples. We work with Lawrenceville HOA boards regularly and can help you prepare the submission. Call (877) 610-2993 and we’ll walk you through it.
No. There is no trip charge inside the county. You’ll also get $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. The price we quote is the price on the invoice, agreed in writing before any work starts. Estimates are free.
If your Lawrenceville gate is sagging, stuck, or the motor runs but nothing moves, call (877) 610-2993 for a free estimate. Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Lawrenceville Customers Say
"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Operator had died and the manufacturer no longer makes the board. Rather than sell me a whole new system he found a compatible unit and adapted the mount. Saved me a great deal of money."
- Salvador Arredondo"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth